You idle out of the ramp and the screen is perfect. Bottom, structure, a bit of bait — all of it clear. Then you put the throttle down, and somewhere around 15 knots the screen turns to static, or the depth reading freezes on the last number it trusted.
Nothing has failed. The sounder is doing exactly what it can with the signal it is being handed. Almost every "my sounder won't read at speed" complaint is a transducer mounting problem, and most of them are fixable in an afternoon with a drill, some sealant and a bit of patience.
Quick answer: the transducer face needs clean, bubble-free water at speed. That means mounting it lower on the transom than you think, angled so the trailing edge sits slightly deeper than the leading edge, at least 300mm clear of the outboard's prop wash, and nowhere near a strake, weld or rivet line that will aerate the flow. If it reads at idle and fails at speed, it is almost always air, not electronics.
Why it works at idle and fails at speed
A transducer needs water, and specifically it needs water without bubbles in it. At idle the hull is barely disturbing anything, so the face sits in solid water and the ping goes out cleanly. As speed climbs, the hull starts shedding air, the transom gets turbulent, and any small imperfection ahead of the transducer starts feeding a stream of bubbles across the face.
Sound does not travel usefully through a bubble layer. The pulse hits the aerated water, scatters, and comes back as noise — or never comes back at all. That is why the failure is speed-dependent and why it feels like the unit is cutting out. The electronics are fine. The water is wrong.
The three places air gets in
First, the hull itself: strakes, chines, weld beads, rows of rivets and transducer brackets all shed vortices. Second, the outboard: prop wash and the turbulent plume behind the leg will ruin anything mounted in line with it. Third, the mount: a bracket that sits proud of the hull, a face that is not parallel to the waterline, or a trailing edge that lifts will all create their own air.
On a pressed aluminium tinny this is more pronounced than on a fibreglass hull, because the hull has more features to trip the flow and because the transom is often shorter and steeper than a glass boat's.
Mount height: the half-inch that decides everything
The single most common error is mounting the transducer too high. It looks right sitting flush with the bottom of the hull, and it will work at idle, which convinces everyone it is fine. At speed the hull lifts, the water drops away, and the face is suddenly running in spray rather than solid water.
The rule of thumb worth starting with: the centre line of the transducer face should sit roughly 3mm below the hull's running surface, with the trailing edge a few millimetres lower again. On most alloy hulls that means the bracket sits low enough that you can feel it below the keel line when you run a straight edge along the bottom.
Set the angle with a straight edge, not by eye
Hold a straight edge along the bottom of the hull and sight it against the transducer face. The face should be parallel to that line, or angled back by a degree or two — the trailing edge slightly deeper than the leading edge. Angled the other way, the face lifts water and the unit loses bottom the moment you accelerate.
Do this with the boat on the trailer on flat ground, and check it again after the first run. Mounts move, especially on the first trip after installation.
Keep it out of the prop wash
Roughly 300mm of clearance from the outboard's centreline is a reasonable minimum for a small tinny, and more is better if the transom allows it. Mount it on the side of the transom that turns into cleaner water for your normal steering direction, which in practice means offsetting opposite the direction the prop torque pulls the hull.
Also look up: a transducer mounted directly below a transducer bracket, a ladder, a sounder cable or a live bait tank outlet is sitting in someone else's turbulence. Everything ahead of the face matters, not just the face itself.
Deal with strakes, welds and rivet rows
On pressed alloy hulls there is often only one clean patch of transom between the last strake and the outboard. If your options are limited, favour a spot with uninterrupted flat plate even if it means going slightly further outboard than you would like.
If the only available spot has a weld bead or rivet line running ahead of it, a small fairing block bedded to the transom can smooth the flow enough to make the difference between reading and not reading.
Wiring and interference: the other half of the problem
Not every dropout is water. A sounder that blanks when you key the radio, run the live bait pump or start the outboard has an electrical problem, and no amount of bracket adjustment will fix it. Voltage sag on a long, thin run to the transom is common on older tinnies.
Run the sounder on its own fused circuit with adequate cable, keep the transducer cable away from the outboard's main harness and any high-current wiring, and check that the transducer plug at the back of the unit is fully seated. A partially seated plug will read fine in the shed and fail in a chop.
Real-world tips from the ramp
- Photograph the install before you silicone it. When the reading is good at 20 knots, take a photo with a tape measure against the transom. That photo is your reference if the bracket ever shifts.
- Test with a mate driving. You need to watch the screen during acceleration to know whether the picture fades gradually (air) or cuts abruptly (power).
- Bed the screws, not just the bracket. Aluminium transoms and stainless fasteners are a corrosion pair; a dab of suitable sealant on each screw prevents the weeping that eventually rots a transom from the inside.
- Don't chase perfection at 40 knots. If it holds bottom to 25 knots and shows structure clearly at trolling speed, you have a good installation. Spend the effort on where you fish instead.
Getting clean power to the transom
A sounder is only as good as the supply behind it, and the same clean 12V that keeps a sounder stable also runs your lights, pump and charging. If you are rewiring a tinny this season, it is worth doing the 12V side properly once — fused distribution, tinned cable, sealed connections and enough capacity to run the electronics without voltage sag at idle.
Our 12V accessories range covers the cabling and connection gear for tidying up a boat's electrics, including the adaptors and power supplies we use on our own boats.
Transducer mounting is unglamorous work, and it is the difference between a sounder you trust and one you stop looking at. Get the face into clean water, keep the supply clean, and test it under throttle rather than at the ramp. If you have a mounting trick that fixed a stubborn install, share it in the comments — the odd combination that works on one hull is often the answer someone else is hunting for.